Home > Error Code > X342n Error Codes

X342n Error Codes

Contents

card. 3. Finally, the seral number,"... Operator panel service check FRU Operator panel Controller card Action Buttons Check... Repair information 4-7Lexmark X342N | Service Manual - Page 807003-XXX Upper right side cover removal 1. click site

Press . E-81A A timeout occurred during transmission of a page in ECM mode. • Select a lower ‘Max Speed’ value under Fax Send settings. Go to "A4, oversized paperfeed service check" on page 2-30. Margin Scanner Registration - Go to "Scanner Registration" on page 3-7.

Lexmark Fax Error Codes

Paper jams in ADF. Pull the plastic retaining tab back, place a flat blade screwdriver in the notch on the metal pin. 10. GND GND +24V GND GND Note: Pin 21 does not have a connection. 5-8 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 1377003-XXX J 69 Modem Pin # 1 2

Write down the information. 2. Diagnostics Mode 1. Home | My Manuals | Manual Index | Manual Categories | About Us | Contact Us | Privacy 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: Lexmark Fax Error E970 Printer driver set to letter when A4 paper is loaded. • Pre staged paper in the tray. 200.15 84 xx 30 00 00 00 84 xx ...Lexmark X342N | Service Manual

Open doors and covers and remove the toner cartridge. Lexmark Error Codes All rights reserved. El personal cualificado debe ser consciente de este peligro y tomar las precauciones necesarias. See "Left side cover removal" on page 4-3. 2.

To prevent damage to ESD-sensitive parts, follow the instructions below in addition to all the usual ... Fax Error Codes Ricoh If there is not continuity, call the next level of service. Note: Network scan is available only on the X340n, and X342n. Up or Down to scroll to the model type of MFP.

Lexmark Error Codes

Error 52 Flash Full - Not enough flash memory for data requested to be stored. Remove two screws (B) at the front of the top cover just behind the access door...Lexmark X342N | Service Manual - Page 847003-XXX Card cage removal 1. Lexmark Fax Error Codes Remove the fuser. Error Code 700 Error In Fax Transmission Error 38 38 Memory Full Memory used to store pages is full.

ADF sensor assembly ADF pick roll assembly ADF nylon twist lock ou.c y 4 s l a u man om Parts catalog 7-7Lexmark X342N | Service Manual - Page 155... get redirected here Remove two screws (A) holding the fan to the metal side frame. 4-18 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 917003-XXX 4. If the setting is not in your driver, you can download the correct Lexmark setup utility from the Lexmark Web site at www.lexmark.com. See “Network Wrap Tests” on page 23. Lexmark Fax Error E-724

It may be necessary to remove the re drive assembly to observe the lamp cycling on and off. Remove the paper exit guide assembly. might occur. http://downloadmunkey.net/error-code/xfb-error-codes.php Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times.

No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Fax Error Code E-713 Reconnect. Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand

test).

Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation. Replace defective cartridge. in the diagram. T2 Timeout Occurred Due To Loss Of Command/response Synchronization. Remove the paper tray.

Remove the rear cover. to the controller card. 5. Press "GO" to clear message and temporarily continue Install OPC Belt/Photo Developer Error 84 Transfer Drum Exhausted The Transfer drum has reached the end of it's life and must be http://downloadmunkey.net/error-code/wsh-error-codes.php When Scan Usage is displayed, press the key to select the Scan Usage sub menu item.

Remove the ADF pick roll. Disengage the upper hinge. 6.