Home > Error Code > Xts 3000 Error 09/10

Xts 3000 Error 09/10

Contents

Observe the gauge for approximately 1 minute.•If the needle falls 1 in. Use Error Code FAIL 001 FAIL 002 9.3 Receiver Troubleshooting Table 9–3 lists the possible causes of, and corrections for, receiver problems. MIL-STD-810C, Method 512.1, Procedure I, MIL-STD-810D, Method 512.2, Procedure I, and MIL-STD-810E, Method 512.3, Procedure I, which require the radio to maintain watertight integrity when immersed in three feet of water Thanks for the info. « Previous Thread | Next Thread » Thread Tools Show Printable Version Email this Page Display Modes Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

The host processor is the master on this bus, while the secure module is a slave on the bus. Problems detected during these tests are presented as error codes on the radio display. This data is passed to the DSP via an interface with the ADSIC (U406) for appropriate processing.The ADSIC interface with the ABACUS comprises the four signals: SBI, DIN, DIN*, and ODC They will be in one of three formats: ER xx/yy or ERROR xx/yy FL xx/yy or FAIL xx/yy FAIL nnn Where "xx" and "yy" will be hexadecimal characters (0-9, A-F), and

Motorola Xtl 5000 Error Codes

You may have to register before you can post: click the register link above to proceed. The pressure should drop slowly to “0.”9. The signals are shown in Figure 12. It then waits for a message from the MCU that the ADSIC has been configured, before going on.During this process, the MCU does power diagnostics.

Among these are expanded input/output (I/O), memory decoding and management, and interrupt control. The internal 512 bytes of EEPROM, along with the external EEPROM, are used for non-volatile storage of customer-specific information. When +5Vdc has been established, it is sensed by the supervisory IC, U726, which disables the system reset through the delay circuit R208 and C214.When the MCU comes out of reset, Fail 01/90 Anyone find a copy?

The transmit side of the SSI port consists of SC2, SCK, and STD. Motorola Apx 7500 Error Codes Drop the board in place.c. Troubleshoot Control Unit AB FAIL 05/84 Control Unit EEPROM blank. The DSP accesses this data through the parallel data bus parallel configuration bus consisting of D8-D23, A0-A2, A13-A15, RD*, and WR*.

Press the display locator pad (39) down over the three locator tabs on the casting.14.Reinstall the main seal (58) around the casting assembly (54). Xts5000 Fail 01/82 The message is ERROR 09/10. This is in contrast to a typical linear type regulator, which basically shunts unused current to ground through an active resistive divider. Controller Board Refer to Figure 7 and the appropriate schematic diagramThe controller board consists almost entirely of digital logic comprising a microcontrol unit (MCU — U701), a custom support logic IC

Motorola Apx 7500 Error Codes

In the fundamental mode of operation, the ADSIC transfers raw IF data to the DSP. Power-Up Error Code Displays (Continued) Description Table 9–2 to aid in understanding particular operational error codes. Motorola Xtl 5000 Error Codes Top Pj Moderator Posts: 5125 Joined: Sun Sep 09, 2001 4:00 pm What radios do you own?: X9000 thru APX Location: Batboard Helpdesk Contact: Contact Pj AOL Re: Any way to Motorola Error Codes The key can be infinite key retention or 30-seconds key retention, depending on how the code plug is setup.The radio’ s host processor communicates with the Secure Module on the Serial

Dead Battery 2. Selecting clear mode pulls this signal to logic low. Sign In Upload Page of 170 Go Download Table of ContentsContents Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Comment Manuals Brands MOTOROLA Manuals Portable Radio HT 1000 SBI is a programming data line for the ABACUS. Motorola Apx Error Codes

The new XTL is running R12 and is working great except for no DES. Keep the vent port covered with your thumb while the radio is submersed.7. Note that many of the displayed codes are similar to those in the Astro Spectra radios. It then configures the ADSIC via the SPI bus, configuring, among other things, the DSP memory map.

If the pad is attached to the RF board, remove it from the board. Motorola Xtl 2500 Error Codes The UNSW_B+ provides power to the secure module as long as the radio battery is in place.Key variables are loaded into the secure module through connector J601, pin 15. It is not possible for a codeplug to self inhibt, despite what you do to it Two reason for the fail code, cps has been interrupted when writing "like you said"

Batboard Batboard Forum - Please go back to using batboard.batlabs.com URL.

There are 36 configuration registers in the ADSIC, of which four contain configuration data for the ABACUS. As with the vacuum pump kit above, the NTN9279A adapter connects the pressure hose to the radio's casting.!C a u t i o n 8-6Miscellaneous Hardware Other items needed for testing The system returned: (22) Invalid argument The remote host or network may be down. Motorola Xts 2500 Error Code 09/10 This is the same control line from the MCU, which controls the series pass element Q106, that switches SW_B+.

Location: Tijeras NM US Quote Postby abbylind » Mon Jul 22, 2002 10:57 am Yep no secure board onboard! It is a two-wire duplex bus, used to connect to external data devices. turn on radio get FAIL 01/82 error. Keep the vent port covered with your thumb until the test is complete (through step 8). 5.

Display Possible Cause Remedy Cond ERROR 01/02ERROR 01/82 Radio has an error with its EEPROM; one or more modes in the radio have an incorrect pattern in the Memory Board EEPROM.Radio D23 high, or MODC low out of reset, causes the DSP to seek code from the FLASH ROM (U404). A stream of bubbles indicates a sign of leakage.NOTE: Some air entrapment may cause the accumulationof bubbles, especially in the grille area, but thebubbles should not be continuous.8. When reading the theory of operation, refer to your appropriate schematic and component location diagrams located in the back section of this manual.

Please review them for posting guidelines and further clarification. Top GEMOTO Posts: 415 Joined: Fri Jan 09, 2004 6:15 pm Location: United States of America Re: Any way to determine type of secure module w/o disassembling Quote Postby GEMOTO »