Home > Socket Error > Wsa Error 10035

Wsa Error 10035

Contents

WSA_QOS_REQUEST_CONFIRMED 11009 QoS request confirmed. This error is returned from operations on nonblocking sockets that cannot be completed immediately, for example recv when no data is queued to be read from the socket. So, for example, you can expect this error if a WinSock implementation doesn't support socket type SOCK_RAW within the Internet address family (AF_INET). This error signifies that an attempt was made to access a file (or, in some cases, a directory) in a way that is incompatible with the file's attributes.

WinSock functions: WSAENOTSOCK (10038) Socket operation on non-socket. Either the socket handle parameter did not reference a valid socket, or for select, a member of an fd_set was not valid. PKCS1 signing not recommended? Berkeley description: A protocol was specified that does not support the semantics of the socket type requested.

What Is A Socket Error

This error occurs if the sin_addr is INADDR_ANY (i.e. WinSock description: No equivalent. i will give it a day ..if everything works fine i shall mark this thread resolved.. If an error occurs at the server side an error should also occur at the client side.

WinSock functions: recv(), recvfrom(), sendto(), FD_CLOSE Additional functions: send() can also fail with WSAECONNABORTED. WinSock functions: WSAESHUTDOWN (10058) Cannot send after socket shutdown. Developer suggestion: are you trying to use an optional feature? Socket Error Codes Linux WSA_QOS_RECEIVERS 11005 QoS receivers.

The idea is that when you get a message notifying you of a pending message you call recv() or recvfrom()... Returned when a provider does not return SUCCESS and does not provide an extended error code. and its all done.. The code will wait for the ReadyToSend event (the ready boolean flag), and loop.

Berkeley description: A socket operation was attempted to an unreachable host. Socket Error 10061 Connection Refused WSAESHUTDOWN 10058 Cannot send after socket shutdown. The WSAGetLastError function returns the last error that occurred for the calling thread. WinSock description: Same as Berkeley.

Socket Error 10053

If so, then the application might have had a problem resolving the name (see suggestions at WSATRY_AGAIN for more information). WinSock description: Similar to Berkeley & Microsoft C, the generic meaning is that an application passed invalid input parameter in a function call. What Is A Socket Error SO_ACCEPTCONN, SO_ERROR, SO_TYPE: are read-only options, so they work with getsockopt(), but not with setsockopt() Developer suggestions: Check the parameters. Socket Error 10049 Berkeley description: A request to send data was disallowed because the socket had already been shut down with a previous shutdown() call.

Some of the types of things you will find under some errors are: Microsoft C description: the first few WinSock errors are carry-overs from the standard 'C' runtime library. This is usually caused by one or more of the function pointers being NULL. Is there a way to calculate the approximate remaining buffer (client or server side) size?Any help would be appreciated,Thanks, Left by Sen on Nov 03, 2008 9:53 AM # re: Winsock The code can be as simple as this:procedure SendToClient(ID: integer; S: String);var i: integer;begin ipServer.DataToSend[ID] := S; i := ipServer.BytesSent[ID];end;In the above example i always returns 0 even though it sent Socket Error 10054 Connection Reset By Peer

See other suggestions under WSAECONNABORTED. WinSock functions: Additional functions: any function that takes a socket (or file handle) as an input parameter See also: WSAENOTSOCK WSAECONNABORTED (10053) Software caused connection abort. Yes! I'm using version 8.0.3022.0 so I guess I'll contact live support.

If you are using a name server(s), check whether the server host(s) are up (e.g. Wsaewouldblock Sap It is normal for WSAEWOULDBLOCK to be reported as the result from calling connect on a nonblocking SOCK_STREAM socket, since some time must elapse for the connection to be established. WinSock description: Same as Berkeley TCP/IP scenario: In TCP terms (datastream sockets), it means an attempt to connect (by sending a TCP SYN packet) caused the destination host to respond to

Microsoft C description: Bad file number.

Of the two that can fail, neither of them set an error value you can retrieve from WSAGetLastError() (refer to Chapter 10, "Support Routines" for more information on any of these Return code/valueDescription WSA_INVALID_HANDLE 6 Specified event object handle is invalid. Resource temporarily unavailable. Winsock Error 10061 WinSock description: No equivalent in WinSock.

programming Does Dry Ice Really Cool Five Times Better Than Re... So the code below has been updated to only wait for the event if BytesSent equals 0. copies what it can into your buffer) and fails the function. Too many open sockets.

If you get the WSAEWOULDBLOCK just put your loop to sleep for a few milliseconds (e.g. This could happen with a call to another function later, including connect, listen, WSAConnect, or WSAJoinLeaf. WinSock functions: accept(), listen(), recv(), recvfrom(), send(), sendto() WSAEPFNOSUPPORT (10046) Protocol family not supported. WinSock function: gethostbyaddr(), gethostbyname(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort() See also: WSANO_DATA, WSANO_RECOVERY, WSATRY_AGAIN WSAVERNOTSUPPORTED (10092) WINSOCK.DLL version out of range Berkeley description: No equivalent.

WSA_E_NO_MORE 10110 No more results. The specified file handle is not a valid file-handle value or does not refer to an open file; or an attempt was made to write to a file or device opened WinSock functions: getpeername(), recv(), recvfrom(), send(), sendto(), setsockopt(), shutdown(), FD_CONNECT See also: WSAECONNABORTED, WSAECONNRESET, WSAENETRESET, WSAETIMEDOUT WSAENOTEMPTY (10066) Directory not empty. Every call to recv with this socket returns this error, no matter how long I wait, until I close the connection and try again.

Basically, you want to identify where the problem occurred. while ( connect( g.s, (SOCKADDR*) &clientService, sizeof(clientService) ) == SOCKET_ERROR) { int err = WSAGetLastError(); printf( "Failed to connect: Error code: %d.\n", err ); printf( errCodes[ err ] ); //WSACleanup(); //return; Berkeley description: A bad option or level was specified in a getsockopt()(2) or setsockopt(2) call. WinSock description: Same as Berkeley.

Each implementation may have a maximum number of socket handles available, either globally, per process, or per thread.