This is a Zephyr motherboard after all, and this is the one that's got the most inefficient GPU design at 90nm. py3m4n on 2011-03-28 04:17:23 : The southbridge can also be a cause of this error code. There are two theories to fixing this one deals with the "X" clamps that hold down the chips. Now, I have to apply the 12V fan mod to this Xbox 360 Elite. click site
On Sale Now 1 Answer Filter by: Most Helpful Newest Oldest Chosen Solution oldturkey03 @oldturkey03 Rep: 371.8k OTS 596 268 1.1k Posted: 01/09/2013 Options Permalink History ericambrose32, this error is caused Bu videoyu Daha Sonra İzle oynatma listesine eklemek için oturum açın Ekle Oynatma listeleri yükleniyor... Yükleniyor... Ace06-19-2010, 03:33 PMA hair dryer doesn't output enough heat to melt the solder.
Version 3.17 brings support for the new dashboard 17502. MS will fix it promptly and for free and if you open it you loose the free support.Check the documentation that came with your Xbox 360 for contact information.In the US A lot of the information you are getting here has been collected in the community, so thanks to everybody who shared his misery! I've done this on two different computers, and both give these constant errors, but every time I dump the NAND, I get different errors at different places.
Make sure the DVD drive is of the same version originally included with the console and that it is using either the original firmware included with the console or newer. Reballed the GPU but still 0102. The same thing happens with the Xbox 360's GPU: the solder joints are too weak, they heat up, and break. P0102 Yes, it may work, but in the long run, you will destroy the GPU.
I would personally recommend to apply the 12V fan mod to ALL motherboards, even if pre-Jasper systems will make a ton of noise. 0102 Phone Number Right now, NANDPro is writing to block 0x0001A1. There are two ways to fix it. This error code will help the person who is fixing your xbox 360 narrow down the problem and better get your 360 fixed correctly.
I've already redid heatsinks thermal paste on both GPU and CPU, and it seems to work fine for about 10 min, then it goes back to this error. This can also be caused by the tray not being fully closed on boot. contact MS to get a free replacement console before attempting to fix this yourself. About 55-60% of the 3RROD units has this 0102 secondary error code.
UPDATE: I've erased the NAND and am now flashing FreeBOOT again. You need to let the flux go in between the die and the motherboard, as that's where the solder is. Xbox 360 Reball Could this cause the dumps to take this long? 0102 Country Code Ekle Bu videoyu daha sonra tekrar izlemek mi istiyorsunuz?
Remember this when you reflow the solder: -Use a heat gun that goes up to between 400 and 450 degrees Celsius -Heat up the area under the motherboard where the GPU get redirected here That will solve a lot of minor problems (like random E79, odd lights on the RoL and problems with the Play and Charge cable). over torquing of the AV or heatsync bolts can cause this error.E09: Unconfirmed: This can be caused by two completely different things either: A. To keep the fans at the standard voltage would just bring this Xbox 360 back to its non-working state. Xbox 360 Error Codes
JYP666 on 2013-04-01 16:28:11 : 0102 on a Xenon board. Anyway, what else can i do? The other Xenon with 0102 managed to get that same error SEVEN TIMES since I got it! navigate to this website I add the fans, I would if I was you.
If you attempt this you do so at your own risk. Ace07-07-2010, 12:53 AMUpdate on the repair process for the store: I can tell you one thing - Xbox 360s with a Xenon motherboard suck. hellrazor006 on 2012-02-23 23:02:56 : this code kept coming back and i just couldnt get rid and also the drive was knackered however ive just tried my new dry reflow profile
Used aluminum foil on GPU as a last attempt. References: No References available! Learn more You're viewing YouTube in Turkish. I could have swore it was a 8, im sure thats what I used...
Is a normal hair dryer enough to make the reflow? Now, I just keep getting constant errors every time I try to read from the damn NAND, but never at the same place and never the same errors, either. goodolick on 2011-07-30 18:01:17 : Can confirm sometimes CPU. So far there is 1 major theory for what causes most of these errors is that the Ram, CPU, or GPU are not soldered properly to the mother board due either
Either by using this guide and kit or by reflowing/reballing the CPU, GPU and RAM. That includes running it in a >85 degree room or in a cramped location. (knock on wood) Ace06-19-2010, 11:56 PMThe heat sensor that shuts off the Xbox 360 is located in Generated Sat, 05 Nov 2016 17:41:27 GMT by s_hp90 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://forums.xbox-scene.com/index.php?/topic/611353-xbox-360-3-red-light-error-0020-fix/ Unable