Home > Zanussi Washing > Zanussi Ele Error Code

Zanussi Ele Error Code

Contents

how-2-repair.com 38,643 views 10:39 How to enter diagnostic test mode on tumble dryers Aeg, Electrolux, Zanussi Etc - Duration: 8:47. Sign in 70 6 Don't like this video? E54 Motor relay contacts sticking As above. This feature is not available right now. check over here

All readings should be between 3 and 6 Ohms.If readings are correct, check wiring from motor to motor control board, If good, replace motor control board. Safety drain. E42Door lock device failureSee E41See E41 E44Door closed sensing failure.See E41See E41 E45Line door sensing failure.See E41See E41 E46Door command sense.See E41See E41 E49Door incongruence between door line and door sense.See Search Fixya Press enter to search.

Zanussi Washing Machine Error Codes

Before you start any investigation of the fault or even remove the lid of your Zanussi washing machine or washer dryer please read and fully understand this article in full and eSpares 641,865 views 4:24 How to Diagnose Washing Machine Control and Program Problems - Duration: 9:08. E45 Problems with the sensing circuit of the triac that actions the door interlock As E43.

Parts Email Can't find a part you need? Expert: Techdesk replied5 years ago. Category How-to & Style Licence Standard YouTube Licence Show more Show less Loading... Zanussi Washing Machine Error E21 E13Water leak in tub or air leak in air bell.1.

characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 92 7223451 Skip to main content About Us Contact Us Call 0844 9777 888 (7p Zanussi Washing Machine Fault Finding Loading... Disconnect the plug from the drive motor and measure the resistance pins 4 & 5 in the motor.If the reading is between 105 & 130 Ohms, replace the motor control board. Please, don't guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.

Still E41 - got to pop out will be back later this afternoon. Zanussi Washing Machine Error Codes E10 Note the error code displayed. Transcript The interactive transcript could not be loaded. RESET E5dLine interference, Wiring defective, defective main board or inverter board.

Zanussi Washing Machine Fault Finding

CRM board faulty. Paul Charmbury says : Reply October 12, 2016 at 5:25 pm sorry for the late reply Try checking the capacitor on the motor I believe on this model you need to Zanussi Washing Machine Error Codes Hiya,OK, thanks for that.Check the error codes stored again.If it's still E41 the machine isn't detecting a fault.Thanks Ask Your Own UK Appliance Question Customer: replied5 years ago. Zanussi Washing Machine Error Codes E20 Give the author +30 points!

Overheating caused by continuous operation or ambient conditions (let appliance cool down). http://downloadmunkey.net/zanussi-washing/zanussi-e60-error-code.php Doubting myself now. No restriction. The filter in the inlet hose is blocked.Clean the water inlet hose filter. Zanussi Washing Machine Reset

I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. Today went to put a wash on and it just wouldnt do anything showing the same lock display. I think it came up straight away but would like to be sure. this content E41 Door open Close the door!

I have a Electrolux EDC 78550W tumble dryer with a TC3 facial panel. Zanussi Washing Machine Not Working Cycle blocked, door locked (after 5 attempts). Close the door correctly.

Cycle paused, door closed Start E21Difficulties in draining Drain hose kinked/blocked/incorrectly positioned; Drain filter clogged or dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; Circuit board faulty; Current leakage from

E37 Sensing circuit of 1st level pressure switch faulty As above E39 HV sensing circuit of anti-overflow pressure switch faulty As Above E40 Door open, door interlock, wiring or main PCB Possible causes are faulty door interlock or door circuit triac on the main PCB.Most likely cause is the door interlock. Bill Newberry 717,894 views 10:43 Zanussi Timeline STRIPDOWN. Zanussi Dishwasher Error Codes Doesn't finish sticks on 0.01 and will just carry on.

Cycle blocked, door locked (after 5 attempts). If this does not help and the error code reappears the inspector of the laundry must be contacted. Help ! http://downloadmunkey.net/zanussi-washing/zanussi-error-code-10.php Switch the hoses to correct position No.

Possible fault Motor faulty; Wiring faulty; Electronic board faulty. E93 Incorrect machine configuration As above. Cycle paused, door closed Start E13Water leakage Drain hose incorrectly positioned; Water pressure insufficient; Water fill solenoid faulty; Leaks or blockage in pressure switch hydraulic circuit; Pressure switch faulty; Circuit board Apart from that there are often lower cost compatible spares available that we may be able to recommend that can offer you a considerable saving.

NOTE! Show more Loading... The RINSE display flashes.The washing is not sufficiently spun. Cycle blocked, door locked (after 5 attempts).

E71 NTC washing sensor faulty Self explanatory but do also check the wiring to the temperature probe. Possible fault Board wiring; board faulty. I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. Cycle interrupted.ON/OFF RESET E9F PCB.Cycle interrupted.OFF/ON EH1Power supply problems (incorrect / disturbance); PCB faulty.

It's easy with eSpares. Machine Status/Action Cycle interrupted. Please enter a valid email address. This may also be due to a block to pump or a broken control.

What could this be? or it's affiliates. Cycle blocked, door lockedRESET E54PCB faulty; current leakage from motor or from wiringCycle blocked, door locked (after 5 attempts). Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts

You can't post answers that contain an email address. Drain pump functions always (5 min., then it stops for 5 min. during the execution of the washing programme): Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display Cycle is paused with door locked.