Home > Zanussi Washing > Zanussi Jetsystem 1400 Error Codes

Zanussi Jetsystem 1400 Error Codes

Contents

suegoldsmith - June 22 Reply It shows me E72,what i have to do? eSpares 63,379 views 4:04 How to Replace a Zanussi Tumble Dryer Drive Belt - Duration: 14:43. Press and hold together the start button (the one with the green arrow) and the button to the left of it. The timer does not advance????? check over here

It was door locking mechanism (inside machine, not the door catch) had burnt out. The reason for this is that in order to replace many of these electronic modules it is required that the board is programmed and this is beyond the scope of a https://t.co/ZCIjeG4r4X Follow Martin NewsBlog PPI claimants told to contact card companies for refunds after claims firm goes bust NEVER pay to reclaim PPI 10,000s of NHS staff facing tax You do not need to reset the machine to get rid of the fault code as this is automatically deleted.Run an empty load with no detergent in an attempt to get

Zanussi Washing Machine Error Codes E40

Came across this solution and, bingo, it worked. BUT when we switched the machine on it came up with error code E90. the water is turned off2.the water pressure is too low.3.the solenoid valve is open circuit4.there is a problem with the pressure switch (least likely)Cold valve is at the end of blue

This is not a DIY repair. My brother was using my washing machine and that code came up. Model number 3. Zanussi Dishwasher Error Codes MegaShopBot.com Instantly searches the best shopping comparison sites.

Thanks bev Preston...

Click here for the answerBosch Washing machine - Drum does not rotate?

We did a 2nd wash this morning (the first was fine). Zanussi Washing Machine Error Codes E10 I looked on this site but was referred to something about "Interlock" but nothing was explained what that is,does or how to fix it. Contacts Martin Lewis is a registered trade mark belonging to Martin S Lewis. If they make a mistake they have to pay for a replacement board, if you make a mistake then it would be you paying for it and it's not worth the

Saved me some money.

Larry
Oct 2016


Mend it How can I fix my PSP? Zanussi Washing Machine Not Working It performed OK but error E13 appeared at the end. pixiechick 965Posts 4,222Thanks pixiechick By pixiechick 18th Apr 08, 8:45 AM 965 Posts 4,222 Thanks pixiechick View public profile Send private message Find more posts View all thanked posts #5 This may be due to a blocked or trapped pipe or a problem with the valves.

Zanussi Washing Machine Error Codes E10

E24 Sensing circuit of the component (triac) that controls the drain pump faulty As above. This info does not constitute financial advice, always do your own research on top to ensure it's right for your specific circumstances and remember we focus on rates not service. Zanussi Washing Machine Error Codes E40 After 20mins 0.02 and spin sign with cross through it has came up. Zanussi Washing Machine Error Codes E20 Transcript The interactive transcript could not be loaded.

This is most likely caused by a blockage so check the filter and the pump behind for any debris that might be stuck. check my blog ck October 2008 Tweet Add An Answer Form Add your answer using the form below ... Should read about 4000 ohms.My money would be on the solenoid coil being open circuit. Grabbit while you can It's Gone, but was it any good? Zanussi Washing Machine Error E21

Your basket is empty. 0 items in your basket Sub total: £0.00 Go to Basket Currency British pounds Euros Delivery destination United Kingdom Afghanistan Albania Algeria American Samoa Andorra Angola Anguilla Note the error code displayed. Have a manual for Zanussi WJS1265W Front Load Washer/Dryer? this content All you need to do if locate the pump underneath your machine, it will be of a black "squishy" material held in place by silver clips, these are quite hard to

I cleaned all the pipes, checked motor brushes, oiled and checked motors, no benefit. Zanussi Washing Machine Error Codes E30 Mar 03, 2007 | Zanussi WJS1265W Front Load Washer/Dryer Not finding what you are looking for? How to diagnose the problem & test valves pressure switche - Duration: 7:07.

Only 9 digits) How do I find it?

Parts Email Looking for a part you need? About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! MoneySavers Arms The Money Savers Arms Funny Money Money Saving Polls Join Login See Today's Posts Thread Tools Show Printable Version Print Thread Email this Page FIRST POST pixiechick Zanussi Washing Machine Not Spinning Search for - zanussi, jetstream, 1400, e40, error, code, flashing
ours just did same.

Login & Quick Reply Multi-Quote Added Quote Multi-quote Added to Spam Report Share on Facebook Share on Twitter Sorry! E23 Malfunction of drain pump triac This refers to the triac that controls the pump function on the main controller. kwatt - I'd searched the whitegoodsd site but thought it was similar to the others mentioned. http://downloadmunkey.net/zanussi-washing/zanussi-aquacycle-1400-error-codes.php Ruthy1950 14,930 views 8:10 Loading more suggestions...

Loading... Thanks Jan 10, 2010 | Zanussi IZ161S Front Load Washer 1 Answer It has a E10 fault code now it stops every 2 min beeping and it not pulling in enough